Clemas & Co TENNANT T5 Spezifikationen

TENNANT T5 SCRUBBER DRYER OPERATOR MANUAL Clemas & Co. Unit 5 Ashchurch Business Centre, Alexandra Way, Tewkesbury, Gl

OPERATION ENTennant T5 (06--06)11Double row ofbristlesFIG. 134. Check the brushes to ensure they are properlyadjusted (See ADJUSTING SCRUB HEADBRUSHES

EN OPERATION12Tennant T5 (06--06)MACHINE OPERATIONFOR SAFETY: Do not operate machine, unlessoperator manual is read and understood.W ARNING: Fire Or E

OPERATION ENTennant T5 (06--06)13FIG. 227. Adjust the speed control knob to a desiredscrubbing speed (Figure 23).NOTE: 45--60 meters per minute is the

EN OPERATION14Tennant T5 (06--06)BATTERY CHARGE LEVEL INDICATORThe battery charge level indicator displays the chargelevel of the batteries (Figure 26

OPERATION ENTennant T5 (06--06)15Operating the Off-- Aisle Wand:1. T urn the key and wand switch to the on ( I )position (Figure 31). The FaST system

EN OPERATION16Tennant T5 (06--06)DRAINING SOLUTION TANK1. To drain remaining water from the solution tank,pull the solution tank level hose off the ho

OPERATION ENTennant T5 (09--06)17To change the setting, unplug the charger, peel up thecorner of the display label and set the switchesaccordingly (Fi

EN OPERATION18Tennant T5 (06--06)ON--BOARD BATTERY CHARGER ERROR CODESDISPLAY CODEFAULT SOLUTIONbat Loose or damaged battery cable Check battery cable

OPERATION ENTennant T5 (06--06)19ADJUSTING SCRUB HEAD BRUSHESTo ensure optimum scrubbing performance periodicallycheck the scrub head for proper adjus

EN OPERATION20Tennant T5 (06--06)To Adjust an Uneven Brush Pattern:Tools required: Measuring device, 27mm wrench and24mm wrench1. Measure the distance

OPERATION ENTennant T5 (06--06)3TABLE OF CONTENTSSAFETY PRECAUTIONS 4...SAFETY LABELS 5...MACHINE COMPONENTS

OPERATION ENTennant T5 (06--06)21MACHINE MAINTENANCETo keep the machine in good working condition, it’simportant that the following maintenance proced

EN OPERATION22Tennant T5 (06--06)8. Empty and rinse out the debris trough (Figure 63).Cylindrical Brush ModelFIG. 639. Inspect the cylindrical brushes

OPERATION ENTennant T5 (06--06)2314. Inspect the condition of the scrub head skirt,replace if worn or damaged (Figure 69).Cylindrical Brush ModelFIG.

EN OPERATION24Tennant T5 (06--06)5. Clean the parking brake clamp with a cleaningsolvent.6. Check the machine for loose nuts and bolts.7. Check the ma

OPERATION ENTennant T5 (06--06)252. Replace or rotate the rear blade to a new wipingedge and replace band (Figure 79).FIG. 793. To change the front bl

EN OPERATION26Tennant T5 (06--06)JACKING UP MACHINEUse the designated locations to jack up the machine forservice (Figure 84). Empty the recovery and

OPERATION ENTennant T5 (06--06)27TROUBLESHOOTINGPROBLEM CAUSE SOLUTIONMachine will not operate Discharged batteries Charge batteriesEmergency--stop bu

EN OPERATION28Tennant T5 (06--06)TROUBLESHOOTING -- ContinuedPROBLEM CAUSE SOLUTIONPoor water pickup Recovery tank is full or excessivefoam buildupDra

OPERATION ENTennant T5 (06--06)29CONTROL PANEL FAULT INDICATOR CODESThe control panel fault indicator lights will display the following codes when the

EN OPERATION30Tennant T5 (06--06)MACHINE SPECIFICATIONSMODEL Disk,600 mmDisk,700 mmDisk,800 mmCylindrical,650 mmCylindrical,800 mmLENGTH 1350 mmWIDTH

EN OPERATION4Tennant T5 (06--06)SAFETY PRECAUTIONSThis machine is intended for industrial andcommercial use. It is designed exclusively to scrubhard f

OPERATION ENTennant T5 (06--06)31FaST SYSTEM Disk,600 mmDisk,700 mmDisk,800 mmCylindrical,650 mmCylindrical,800 mmPRODUCTIVITY RATEEstimated Actual186

OPERATION ENTennant T5 (06--06)56. When loading/unloading machine onto/offtruck or trailer:-- Drain tanks before loading.-- Use a ramp that can suppor

EN OPERATION6Tennant T5 (06--06)MACHINE COMPONENTS12678549113271314151618152120191724232526221028121. Control Handle2. Control Handle Start Bail3. Upp

OPERATION ENTennant T5 (06--06)7CONTROL PANEL COMPONENTS56101112141323147981. Speed control knob2. 1--STEP scrub button3. Brush pressure increase butt

EN OPERATION8Tennant T5 (06--06)MACHINE INSTALLATIONUNCRATING MACHINE1. Carefully check the shipping crate for signs ofdamage. Report damage at once t

OPERATION ENTennant T5 (06--06)9HOW THE MACHINE WORKSConventional Scrubbing:W ater and detergent from the solution tank flow to thefloor through a sol

EN OPERATION10Tennant T5 (06--06)5. Check the squeegee blades for proper deflection.The blades should deflect as shown (Figure 7).FIG. 76. To adjust t